Chevrolet Fulfills 1 Millionth Corvette Restoration Pledge

September 9th, 2015 by

After more than four months and 1,200 man-hours of painstaking
craftsmanship, restoration of the milestone 1 millionth Corvette – a
white 1992 convertible – is complete.

It was unveiled today at the National Corvette Museum, where it
returns as part of the permanent exhibit. The car was damaged on Feb.
12, 2014, when it and seven other rare Corvettes tumbled into a sinkhole
that opened beneath the museum’s Skydome area.

Chevrolet pledged to restore it.

“We felt it was important to restore this extremely significant car
in Corvette’s long, storied history,” said Mark Reuss, General Motors
executive vice president, Global Product Development, Purchasing and
Supply Chain. “When we disassembled it, we found that each employee
involved in building it had signed a part of the car, which was
fantastic and moving to see. It brought the history to life, and
reinforced the importance of the project.”

After recovery from the sinkhole, the 1 millionth Corvette was moved
from the museum to the Design Center on GM’s Technical Center campus in
Warren, Mich., for restoration. Approximately 30 craftspeople and
technicians from GM Design’s Mechanical Assembly group, along with GM
Service Operations, took on the project.  Mechanical Assembly and the
Fabrication Shops at GM Design build concept vehicles and maintain GM’s
historic vehicle collection.  

“As the one and only 1 millionth Corvette, its preservation was
important to us as the designers of the vehicle – and as Corvette
enthusiasts,” said Ed Welburn, vice president of GM Global Design. “The
damage was significant in many ways; however we have one of the most
highly skilled specialty shops and team of people in the industry, so
they were fully prepared to take on the challenge.”

Despite extensive damage, the team, represented by UAW locals 160 and
1869, vowed to preserve and repair as many original components as
possible – a decision that involved posterity as much as history. That’s
because under the skin, the 1 millionth Corvette carried all those
signatures from the Bowling Green Assembly workers who built the car.

Only two signed components couldn’t be saved, so the team had the
autographs scanned, reproduced as transfers and placed on the
replacement parts.

“We went to great lengths to preserve every autograph,” said David
Bolognino, director of GM Global Design Fabrication Operations. “In the
end, we saved every one of them, which was an unexpected and important
element to the restoration.”

One component with a single signature from Bowling Green Assembly
employee Angela Lamb was too damaged to save or even accurately scan for
her autograph. Chevrolet worked with the National Corvette Museum to
secure a new signature from Lamb on the replacement part, so the
1-millionth Corvette will be historically accurate down to the last
signature.

Among the parts replaced were the hood, front fascia and the lower
panels between the front wheels and doors, as well as a number of
ancillary supporting components under the hood. The replacements came
from a vehicle of the same vintage and color, ensuring authenticity of
the parts and materials involved with the restoration.

A few other components, such as the rear fascia and front exhaust
system, would have probably been replaced in almost any other
restoration project, but the team repaired them because they were also
covered in signatures.

Additional highlights from the restoration:

  • The front sub-frame was damaged in the fall into the sinkhole and required straightening
  • The wheels were damaged, but reconditioned, with the original Goodyear Eagle GS-C tires
  • Rather than replace the scuffed and scratched pad on the instrument
    panel, its soft cover was carefully removed and replaced to preserve the
    employee-signed structure beneath it
  • The red leather seats, featuring one-off “1,000,000th Corvette”
    embroidery on the headrests were damaged but deemed irreplaceable, so
    they were restored, including a few replacement patches of carefully
    matched hide
  • The 5.7L LT1 engine, transmission and other drivetrain components were inspected and found to be damage-free

Surprisingly, the one component the team didn’t have to replace was
the crushed windshield header. When the car first rolled into the shop,
an overhead crane was used to raise it enough to make the car drivable,
but the frame pulled up surprisingly close to the original position,
encouraging the team to save it.

“The header restoration was a wonderful surprise for what everyone
assumed would be the toughest aspect of the restoration,” said
Bolognino. “With access to the original specifications, we got it
spot-on – and even the new windshield glass dropped in perfectly.”

The final touch was replacing the unique “1,000,000th” windshield
banner it wore when it rolled off the assembly line 23 years ago. The
computer graphic file used for the original was still available,
allowing creation of an identical banner.

The 1 millionth Corvette is the second sinkhole-damaged Corvette that
Chevrolet has restored. The first, a 2009 Corvette ZR1 prototype known
as the Blue Devil, was only lightly damaged and was returned to its
original condition last fall. The National Corvette Museum will oversee
the restoration of a third car, a 1962 Corvette.

The other five Corvettes swallowed by the sinkhole will remain in
their as-recovered state to preserve the historical significance of the
cars. They will become part of a future sinkhole-themed display at the
museum.

Source: New feed

Posted in Uncategorized